Angewandte

Forschung & Entwicklung

RhySearch fördert Innovation durch Vernetzung und Wissenstransfer zwischen regionalen Hightech-Unternehmen und Forschungsinstitutionen – auch für Hilti.

Dr. Andreas Bong,
Head Corporate Research & Technology Hilti AG

Publikationen Optische Beschichtung

Unsere Mitarbeitenden im Bereich Optische Beschichtung sind anerkannte Experten in ihrem Fachgebiet und publizieren regelmässig wissenschaftliche Arbeiten in Form von Papers, Präsentationen und Vorträgen. 


Zudem unterstützen wir Studierende, die Interesse haben, ihre Studien-, Bachelor- oder Masterarbeit im Bereich Optische Beschichtung zu schreiben. 

Unten finden Sie eine Auswahl der Publikationen.

Publikationen 2021

Influence of Ar-impurities on the wettability of IBS-deposited Y2O3 thin films

Thomas Gischkat, Max Döbeli (ETH Zürich), Andreas Bächli, Roelene Botha, Zoltán Balogh-Michels

The wettability and the control of the contact angle of surfaces are important for various applications. Materials with a water contact angle less than or greater than 90 deg are hydrophilic or hydrophobic, respectively. Most of the binary oxides are hydrophilic, but oxides of rare earth metals and metal atoms with low electronegativity have hydrophobic surfaces. Yttria is one of the materials predicted to have hydrophobic properties. In this work, we investigated the wettability of ion-beam-sputtered Yttria thin films. The measured water contact angles were between 67° and 96°. The concentration of the embedded argon atoms was found to influence the contact angle.

Anyone clicking on the below link button before October 06, 2021 will be taken directly to the article on ScienceDirect. No sign up, registration or fees are required.

Influence of the Secondary Ion Beam Source on the Laser Damage Mechanism and Stress Evolution of IBS Hafnia Layers

I. Stevanovic, Z. Balogh-Michels, V.J. Wittwer1, Th. Südmeyer1, A. Stuck, Th. Gischkat

Published: 28 December 2020

Ion beam sputtered hafnia is a preferred high index coating material for laser applications. It exhibits a mostly amorphous structure and an adequate laser-induced damage (LIDT) threshold. In this work, we investigated the influence of an assisting ion source on the film stress as well as the LIDT of the sputtered hafnia layers. The stress increases with an increasing ion energy of the assisting ion beam. We identified a maximum compressive stress of 3–3.5 GPa before the film cracks, blisters, and delaminates. Different states of stress lead to different laser-induced damage thresholds and damage morphologies

Laboratoire Temps-Fréquence, Institut de Physique, Université de Neuchâtel, 2000 Neuchâtel, Switzerland

Publikationen 2020

Substrate Cleaning Processes and Their Influence on the Laser Resistance of Anti-Reflective Coatings

Th. Gischkat, D. Schachtler, I. Stevanovic1, Z. Balogh-Michels, R. Botha, A. Bächli, M. Cucinelli2, A. Mocker, M. Gutsche2, S. Günther1,3, P. Alder3, and B. Eiermann1

Published: 27. November 2020

Substrate cleaning prior to coating has a strong influence on the performance of the optical component. Exemplary, none or inadequate cleaning reduces the resistance against laser irradiation drastically. Especially in laser components coated with anti-reflective layers, the interface between substrate and coating is one of the most limiting factors. This study investigates different precision cleaning processes and their influence on the laser resistance of ion-beam sputtered anti-reflective coatings. Therefore, a SiO2/Ta2O5 multilayer anti-reflective coating for a wavelength of 1064 nm and a normal angle of incidence was deposited onto high-quality fused silica substrates. Prior to deposition, the substrates were cleaned with various cleaning processes using different solutions and ultrasonic frequencies. To characterize the cleaned surface quality, the surfaces were analyzed with respect to root-mean-square (RMS) roughness and particle density. Laser damage was measured using a 1064 nm ns-pulsed laser test bench. It was found that an alcoholic pre-clean is recommendable to prevent laser damage caused by organic films remaining from the polishing process. The applied ultrasonic frequencies strongly influenced the particle density down to the sub-micrometer range and in consequence, the laser-induced damage threshold (LIDT). Ultrasonic cleaning at excessive power levels can reduce laser resistance.

WZW Optic AG, Wegenstrasse 18, 9436 Balgach, Switzerland

Institute of Micro Technology and Photonics (IMP), OST—Eastern Switzerland University of Applied Sciences, Werdenbergstrasse 4, 9471 Buchs, Switzerland

UCM AG, Langenhagstrasse 25, 9424 Rheineck, Switzerland

Crystallization of HfO2 thin films and their influence on laser induced damage

Zoltán Balogh-Michels, Igor Stevanovic, Ruggero Frison1, Andreas Bächli, Daniel Schachtler, Thomas Gischkat, Antonia Neels1, Alexander Stuck and Roelene Botha

Published 20. August 2020

We present our investigation on the crystallization of IBS HfO2 on (0001) SiO2. The crystallization was studied by in-situ XRD. The activation energy was 2.6±0.5 eV. The growth follows a two-dimensional mode. LIDT measurements (5000-on-1) with 10 ns pulses at 355 nm on 3QWT HfO2 layers shows that the crystallization leads to increase of the laser irradiation resistance. The 0%-LIDT of the as coated sample was 3.1 J/cm2 and increased to 3.7 J/cm2 after 5h @ 500°C.

1Empa, Center for X-ray Analytics, 8600 Dübendorf ZH, Switzerland

Publikationen 2019

Influence of ultra-sonic frequency during substrate cleaning on the laser resistance of antireflection coatings

Th. Gischkat, D. Schachtler, Z. Balogh-Michels, R. Botha, A. Mocker, B. Eiermann, S. Günther
Published: 20. November 2019, Proc. SPIE 11173, Laser-induced Damage in Optical Materials 2019, 1117317.

Cleaning of substrates prior to optical coating is an important step in the manufacturing of high performance optical components. It is well known that the ultra-sonic frequency used during substrate cleaning has a strong influence on the quality of the cleaning process and the number of remaining particles on the surface. Therefore, we have investigated the influence of ultra-sonic frequency during substrate cleaning on the laser resistance of antireflection coatings. For this purpose, a SiO2 / Ta2O5 AR-coating for a normal angle of incidence at 1064 nm was deposited onto fused silica substrates. Prior to deposition, the substrates were cleaned with cleaning processes. The applied ultra-sonic frequencies were 40, 80, 120 and 500 kHz. After deposition the LIDT was measured using a 1064 nm ns-pulsed laser test bench. It turned out that the different ultra-sonic-cleaning processes have a strong influence on the number of remaining particles on the surface of the cleaned samples. The counted number of particles with sizes greater < 83 nm were between 1320 and 12 particles for the different applied ultra-sonic frequencies. In consequence the different cleaned and AR-coated samples show different laser damage behavior. Nevertheless the measured particle density does not totally explain the differences in laser resistance.

Investigating the Long-Term Stability of LiB3O5 (LBO) Frequency Conversion Crystals at 355nm using Photothermal Deflection and LIDT measurements

R. Botha, H. Cattaneo, M. Stahel, Th. Gischkat, I. Stevanovic, Z. Balogh-Michels, C. Ziolek

Published: in Laser Congress 2019 (ASSL, LAC, LS&C), OSA Technical Digest (Optical Society of America, 2019), paper CM2C.4

 

In order to gain an understanding of the fluctuating long-term stability of LBO crystals, photothermal deflection measurements are used to identify absorbing impurities and defects, followed by multiple pulse LIDT testing to identify possible correlations.

On the Properties of Nanoporous SiO2 Films for Single Layer Antireflection Coating

L. Ghazaryan, Y. Sekman, S. Schröder, Ch. Mühlig, I. Stevanovic, R. Botha, M. Aghaee, M. Creatore, A. Tünnermann, A. Szeghalmi,
Published: 18. March 2019

Single layer antireflection coatings (SLAR) consisting of nanoporous silica (NP SiO2) films are developed by selective chemical etching of atomic layer deposited (ALD) Al2O3:SiO2 composite films. The reflective index of the final NP SiO2 film is finely adjusted from 1.132 to 1.400 at 600 nm wavelength by applying an appropriate ratio in the composite. To meet the requirements of the SLAR coatings from the deep UV (DUV) to the near IR (NIR) spectral range, the film thickness is controlled with nanometer precision by the ALD process. The SLAR are simultaneously applied on both sides of flat or highly curved substrates. Transmittance values above 99.4% are achieved even at a wavelength of 193 nm on fused silica substrates. Various characterization methods demonstrate the advantages of these SLAR with regard to impurities, optical losses, laser induced damage threshold (LIDT) properties, and surface super‐hydrophilicity. The absorption losses at 193 nm wavelength as determined by laser induced deflection measurements amount to approximately 200 ppm, and to approximately 2 ppm at a wavelength of 1064 nm, while the scattering losses are around 30 ppm at 532 nm wavelength for quarter‐wave layers. The LIDT values at 1064 nm are in the range of 93 J cm−2 being close to the values measured on the uncoated substrate.

A new approach to laser polishing and form correction of optical components

H. Kessler, R. Botha, C. Ziolek
Published: 10. September 2019 EPJ Web of Conferences 215

The increasing variety of optical components and materials, combined with stricter surface tolerance requirements, necessitate refining existing polishing processes and developing innovative new polishing solutions and metrology technologies. A fast, reproducible laser polishing process would offer considerable economic benefits over conventional mechanical polishing processes and interest a broad variety of optics manufacturers. In this work, a holistic approach is taken to address the various aspects of glass polishing and form correction via a novel laser polishing system design, the use of a measurement strategy that can be integrated inline and simulation results that are correlated with process parameter studies for different materials.

Publikationen 2018

Laser-induced damage threshold of nanoporous single-layer ALD antireflective coatings, SPIE Proceedings

Th. Gischkat, R. Botha, I. Stevanovic, A. Szeghalmi, L. Ghazaryan, A. Bächli

Published: 16. November 2018

Atomic layer deposition (ALD) enables coating complex shaped substrates with excellent uniformity along the surface of the optic. Recently developed nanoporous SiO2 layers have been applied as single layer antireflection coatings on fused silica substrates at both 1064 nm and 532 nm wavelengths. The LIDT in the nanosecond regime at both 1064 nm and 532 nm of these nanoporous SiO2 coatings as well as the bare substrates were investigated. The stability of the coatings with respect to LIDT has been evaluated under normal atmospheric conditions, dry air with relative humidity < 10% and nitrogen atmosphere. The multiple pulse damage characteristic for 5000 shots showed in all cases no significant pulse dependence. At 532 nm wavelength, the 0%-LIDT value is between 60 J/cm2 and 70 J/cm2, which is comparable to the values measured on uncoated substrates (80 J/cm2). In case of 1064 nm the 0%-LIDT is only between 40 J/cm2 and 50 J/cm2 (uncoated substrate: 100 J/cm2) which is attributed to generated defects during the fabrication process

Influence of substrate cleaning on the laser resistance of antireflective coatings

Th. Gischkat, R. Botha,  I. Stevanovic, M. Cucinelli, S. Günther, A. Bächli

Published: 05. June 2018

Several studies have reported on the detrimental effects of inadequate cleaning on the performance of optical components exposed to laser radiation. The remaining particulates, contaminants or residue located in the coating or on the substrate surface can absorb laser energy and consequently induce damage. To minimize these contaminants, investigations of various cleaning processes have been performed in both the research and industry communities. Transparent published results and comparisons of the different cleaning processes considered, however, are limited due to proprietary considerations. In addition to this, the manufacturing environment, deposition processes, substrate- and deposition materials all have an influence on the effectiveness of a cleaning process. The purpose of this study was to investigate different cleaning procedures and their influence on the laser resistance of ion-beam sputtered antireflective coatings. For this purpose, a SiO2 / Ta2O5 multilayer antireflective coating for a normal angle of incidence at 1064 nm was deposited onto fused silica substrates. Prior to deposition, the substrates were cleaned with a variety of cleaning solutions and procedures and their roughness and surface quality inspected. All samples were characterized in terms of their laser damage threshold using a 1064 nm ns-pulsed test bench and subsequently visually inspected in order to understand the cause of the damage. In this work, the details of the cleaning steps and the corresponding laser damage performance for the different cleaning processes are presented and compared.

Publikationen 2017

Influence of temperature and environment on the laser damage threshold of ion-beam sputtered anti-reflective coatings at 355 nm wavelength

R. Botha, Th. Gischkat, I. Stevanovic, A. Bächli, D. Bischof, M. Michler, S.J. Rinner, C. Ziolek

Published: 13. November 2017

In this investigation the influence of the local environment on the laser damage threshold of anti-reflective coatings is reported. For this purpose, HfO2 / SiO2 anti-reflective coatings were deposited on fused silica substrates using an ionbeam sputter system. Laser damage threshold measurements were performed using two test procedures, S-on-1 and Ron- 1, at 355 nm for temperatures ranging from room temperature up to 250 °C and in different atmospheres. The two test procedures had comparable LIDT results with a possible pre-conditioning effect evidenced by a broadening of the transition range of the R-on-1 measured samples. It was found that samples measured in normal atmospheric air showed superior laser resistance compared to samples measured under nitrogen purge or in dry air. Samples measured in normal atmospheric air also showed a temperature dependence with an improved laser resistance at 25 °C. No temperature dependence was observed for samples measured under nitrogen purge or in dry air. In this paper, literature showing similar effects is reviewed and the influence of a water epilayer on the coating as a possible cause for the observed results is discussed.

Publikationen 2016

Investigation of the Ageing Effects Exhibited by AR Coatings Exposed to ultraviolet laser Irradiation

R. Botha, D. Bischof, B. Vetsch, U. Scherrer, M. Michler, S.J. Rinner, A. Ettemeyer, C. Ziolek

Published: 6. December 2016

Optical coatings used in ultraviolet applications are often exposed to harsh environments operating at elevated temperatures. In order to study the impact of the ageing effects optical coatings experience at various operating temperatures, an ultraviolet laser-induced degradation test system has been developed. It allows for flexible use in both a long-term stability test bench as well as in an LIDT measurement system. This work contains the preliminary results of optical degradation tests at 355 nm performed on anti-reflective coatings. As a subsequent step, the LIDT of the samples were measured using a Q-Switched Nd:YAG laser operating at 1064nm.

Publikationen 2015

Comparative study of the laser damage threshold and optical characteristics of Ta2O5-SiO2 multilayers deposited using various methods

R. Botha, S. Schwyn Thöny, M. Grössl, S. Mourad,C. Maissen, J.I. Venter, Th. Südmeyer, M. Hoffmann, P.V. Bulkin, S. Linz-Dittrich, D. Bischof, M. Michler, S.J. Rinner, A. Ettemeyer

Published: 23. November 2015

Manufacturing processes from the private and academic sectors were used to deposit anti-reflective and high-reflective coatings composed of Ta2O5 - SiO2 multilayers. Used deposition techniques included three Ion Assisted Deposition (IAD) systems and an Ion Beam Sputtering (IBS) system. Coatings were performed on fused silica (Corning 7980) substrates polished by two different suppliers. LIDT Measurements were performed using a Q-Switched Nd:YAG laser operating at 1064nm. The paper presents a comparison of the coatings in terms of laser damage threshold values, optical properties and surface quality.

Unsere Website verwendet Cookies, damit wir die Page fortlaufend verbessern und Ihnen ein optimiertes Besucher-Erlebnis ermöglichen können. Wenn Sie auf dieser Webseite weiterlesen, erklären Sie sich mit der Verwendung von Cookies einverstanden.
Weitere Informationen zu Cookies finden Sie in unserer Datenschutzerklärung.
Wenn Sie das Setzen von Cookies z.B. durch Google Analytics unterbinden möchten, können Sie dies mithilfe dieses Browser Add-Ons einrichten.